Número de parte Descripción Indicator No. To order parts for the VORTEX-GENIE 2 Mixer: Contact your local distributor or visit Please specify Part No., quantity and electric voltage. Do not position the equipment so that it is difficult to disconnect the power cord. PRECAUCIÓN! Unplug from power before cleaning. Refer to “Parts Assembly List” and enclosed multi-fold brochure. Replacement parts are available through most laboratory equipment distributors or directly from Scientific Industries. Keep the unit clean by immediately blotting any spills. The finish can be washed with water (after unplugging) and soap or detergents, using a cloth or sponge. Avoid wetting or unnecessary exposure to fumes. Your VORTEX-GENIE 2 Mixer should be given the care normally required for any electrical appliance. PRECAUCIÓN! If this equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be impaired. They will pop off easily if you lift them, and snap back on again just as easily by aligning the flats and pressing down firmly. All attachments, including the Pop-off Cup and the 3-inch Platform are removable. PRECAUCIÓN! Do not lift your VORTEX-GENIE 2 Mixer by its attachment. The motor will radiate a certain amount of heat that will dissipate by the cast zinc housing. With prolonged use, your VORTEX-GENIE 2 Mixer may become warm to the touch.The VORTEX-GENIE 2 Mixer is now ready to use with the newly installed accessory attachment. Press attachment firmly downward until it “snaps” into place.Alternatively, you may place the attachment on the shaft and turn it until you feel the “flats” aligning.
#Image mixer 3 manual install#
Hold the part you wish to install so the “flat” part of the shaft is aligned with the “flat” of the receptacle in the attachment.A technique of lifting the attachment with your finger tips while using your knuckles as a fulcrum will give you the leverage to remove the installed attachment component smoothly. Grasp the installed attachment and pull straight up until it releases from the shaft.Turn the power OFF by placing the toggle switch into the OFF position.To change accessory mixing attachments, the following sequence is to be followed explicitly.Before re-starting the mixer, re-set the speed control to a setting higher than position 3. After the action has started, you may, if desired, reduce the speed below position 3 for the duration of the run. Nota:: The speed control switch should be set between positions 3 and 10 to enable the mixing action to start. 3.0 before attempting to change attachments. In this mode, you may use any of the accessory attachments available for the VORTEX-GENIE® 2 Mixer.
#Image mixer 3 manual free#
Hands Free mode allows for unattended operation that will continue indefinitely until you stop the mixer by placing the toggle.
Place the toggle switch in the ON position and set the speed control to any position between 3 and 10. Releasing the pressure on the Platform or Cup will stop the mixer. When you touch a vessel to the 3-inch Platform or Pop-off Cup, the mixer will start automatically. A setting of 3 is least vigorous mixing and 10 is the most vigorous mixing. Place the toggle switch in the TOUCH position and set the speed control to any position between 3 and 10.
The VORTEX-GENIE® 2 Mixer has the following modes of operation:.Plug the cord into a properly grounded, three pronged outlet (120 VAC for the G560 model, 230 VAC for the G560E model and 100V for the G560-100V model).This will ensure that the attachment will not come off the mixer during operation. YOU MUST PRESS DOWN HARD WITH YOUR HAND UNTIL YOU HEAR THE ATTACHMENT SNAP IN PLACE.
After you unpack your VORTEX-GENIE 2 Mixer from its protective plastic bag, install either the Pop-off Cup or the 3-inch Platform by first aligning the “flat” part of the mixer shaft with the “flat” part of the attachment. Your VORTEX-GENIE 2 Mixer is supplied with a Pop-off Cup located in the white foam box insert and a 3-inch Platform.
0 kommentar(er)
